Skip to Menu Skip to Search Contact Us Global Websites & Languages Skip to Content
US Flag

You are accessing SGS’s website from the USA.

Visit the US website instead

Stay on the global website and remember my choice

Sample size requirements for FDA 510(k) submission for medical face masks have increased. We suggest taking below actions to safeguard your submission process in a smooth and timely manner.

SAFEGUARDS | Personal Protective EquipmentNO. 163/20

Teenage Girl Wearing Fabric Mask for Protection

Manufacturers wanting to market a Class I, II, or III device intended for human use in the US, for which a Premarket Approval application (PMA) is not required, must submit a 510(k) to the US Food and Drug Administration (FDA), unless the device is exempt from 510(k) requirements of the Federal Food, Drug, and Cosmetic Act (the FD&C Act) and does not exceed the limitations of exemptions in the device classification regulation chapters (e.g. 21 CFR 862.9, 21 CFR 864.9).

A 510(K) is a premarket submission made to the US FDA to demonstrate that the medical device to be marketed is safe and effective, that it is substantially equivalent, to a legally marketed device (section 513(i)(1)(A) FD&C Act). Submitters must compare their device to one or more similar legally marketed devices and make and support their substantial equivalence claims.

In the past, many manufacturers have successfully completed their 510(k) Premarket Notification submission through the US FDA by presenting test reports conducted according to ASTM F2100 on a batch of five samples, minimum, for Differential Pressure, Bacterial Filtration Efficiency (BFE), and Particle Filtration Efficiency, for medical face mask products. Recently, an increasing number of 510(k) review comments have been received showing that the 5-sample test plan may no longer be sufficient to support the 510(k) premarket submission.

The FDA requirements are mainly reflected in the following enforcements:

  1. The provision of test reports covering three non-consecutive batches of medical face mask samples to validate lot-to-lot performance or an explanation of why that method was not followed
  2. A single sampling plan according to the requirements of ISO 2859-1 or ANSI/ASQC Z1.4
  3. Test reports showing that the medical face mask samples satisfy the requirements of ASTM F2100 following an acceptable quality limit (AQL) of 4% to a specific performance class (barrier level)

Based on the expected batch production output of medical face masks, it is impossible for the five-sample test plan to meet this requirement. Following a review of recent FDA 510(k) applications, it is recommended that the sample size for each batch be adjusted to at least 32 mask samples per test, as a conservative approach to avoid any interruption or delay in your FDA submissions. Tests should also be carried out on at least three non-consecutive batches in order to illustrate the quality and consistency of production.

SGS is committed to providing information about development in regulations for consumer products as complimentary services. Through a global network of laboratories, SGS provides a wide range of services including physical/mechanical testing, analytical testing and consultancy work for technical and non-technical parameters applicable to a comprehensive range of consumer products. Please do not hesitate to contact us for further information.

For enquiries, please contact:

Birkoff Chen
Operations Manager
t: +852 2765 3561

Stay on top of regulatory changes within your industry: subscribe to SafeGuardS!

Read more articles for the Consumer Goods and Retail industry

© SGS Group Management SA - 2020 - All rights reserved - SGS is a registered trademark of SGS Group Management SA. This is a publication of SGS, except for 3rd parties’ contents submitted or licensed for use by SGS. SGS neither endorses nor disapproves said 3rd parties contents. This publication is intended to provide technical information and shall not be considered an exhaustive treatment of any subject treated. It is strictly educational and does not replace any legal requirements or applicable regulations. It is not intended to constitute consulting or professional advice. The information contained herein is provided “as is” and SGS does not warrant that it will be error-free or will meet any particular criteria of performance or quality. Do not quote or refer any information herein without SGS’s prior written consent.