Japan Publishes Positive List for Food Contact Synthetic Resin Materials and Articles
Japan has published its Positive List for food contact materials and articles made with synthetic resins. The amendments became effective on June 1, 2020, with a 5-year transitional period.
SAFEGUARDS | Consumer ProductsNO. 092/20
In April 2020, the Japan Ministry of Health, Labor and Welfare (MHLW) published two notifications on food implements, containers and packaging (food contact materials and articles) to amend the Food Sanitation Act. These notifications are:
- Notification No. 196 of 2020 ‘Partial revision of the standards for foods, additives etc.’
- Notification No. 195 of 2020 ‘Amount specified by the MHLW as an amount that does not harm human health under paragraph 3 in Article 18 of the Food Sanitation Act’
Notification No. 196 of 2020 announces the ‘Positive List’ for synthetic resins in food contact materials and articles by requiring these food contact materials and articles to be manufactured using substances in the Positive List. It creates the following four new Positive Lists:
- Base polymers (plastics, Table 1 (1)) with information on the name of each substance, the types of food permitted (acidic, oily/fatty, milk/daily products, alcoholic and others), maximum temperature use, synthetic resin classification and any restrictions
- Base polymers (coatings, Table 1 (2)) with information on the name of each substance, the types of food permitted (acidic, oily/fatty, milk/dairy products, alcoholic and others), maximum temperature use, synthetic resin classification and any restrictions
- Monomers that can be polymerized in trace amounts with respect to the base polymer (Table 1(3)) with information on the name of each substance
- Additives, coatings etc. (Table 2) with information on the restriction of use by synthetic resin category
Notification No. 195 of 2020 supplements paragraph 3 in Article 18 of the Food Sanitation Act, as amended, by considering a migration value of not more than 0.01 mg/kg to be safe for substances not listed in the Positive List for the manufacture of synthetic resin materials and articles that are not in direct contact with food.
The MHLW continues to review the Candidate List of substances for the Positive List that was not completed as of December 23, 2019. This update of existing substances with additional information will be completed by the end of the five-year transitional period and the Positive List may be revised accordingly. In the meantime, the MHLW has also started to review new substances.
According to Article 50-3 of the Food Sanitation Act, the MHLM will set the necessary good manufacturing practice (GMP) guidance. This is the Ordinance for Enforcement of the Food Sanitation Law (Article 66-5). The GMP requirements are based on safety assurance guidelines in the manufacture etc. of food utensils, containers and packaging.
According to the notifications, these became effective on June 1, 2020. Food contact implements, containers and packaging not complying with the Positive List before June 1, 2020, may continue to be manufactured and sold until May 31, 2025.
SGS is committed to providing information about development in regulations for consumer products as complimentary services. Through a global network of laboratories, SGS provides a wide range of services including physical/mechanical testing, analytical testing and consultancy work for technical and non-technical parameters applicable to a comprehensive range of consumer products. Please do not hesitate to contact us for further information.
For enquiries, please contact:
Global Information and Innovation Manager
t: (+852) 2774 7420
Stay on top of regulatory changes within your industry: subscribe to SafeGuardS!
Read more articles for the Consumer Goods and Retail Industry
© SGS Group Management SA - 2020 - All rights reserved - SGS is a registered trademark of SGS Group Management SA. This is a publication of SGS, except for 3rd parties’ contents submitted or licensed for use by SGS. SGS neither endorses nor disapproves said 3rd parties contents. This publication is intended to provide technical information and shall not be considered an exhaustive treatment of any subject treated. It is strictly educational and does not replace any legal requirements or applicable regulations. It is not intended to constitute consulting or professional advice. The information contained herein is provided “as is” and SGS does not warrant that it will be error-free or will meet any particular criteria of performance or quality. Do not quote or refer any information herein without SGS’ prior written consent.