Thailand Proposes New Standard for Toy Safety
Thailand is proposing a mandatory toy safety standard to meet modern-day safety requirements. Comments are accepted until January 13, 2020.
SAFEGUARDS | Toys & Juvenile ProductsNO. 174/19
On November 14, the World Trade Organization (WTO) circulated a proposal from Thailand announcing its intention to replace three existing standards on toy safety with a mandatory toy safety standard, designated as TIS 685 Part-25XX (20XX): Toys: Safety Requirements: Part 1 – Requirements as a Mandatory Standard.
The three existing toy safety standards are:
- TIS 685 Part 1-2540 (1997): Toys: Part 1 - General Requirements
- TIS 685 Part 1-2540 (1997): Toys: Part 2- Packages and Labeling
- TIS 685 Part 1-2540 (1997): Toys: Part 3 - Methods of Test and Analysis
The designated standard contains labeling provisions and requirements for physical and mechanical properties, flammability and chemicals. It contains, inter alia, a number of important changes concerning chemicals. These include:
- Replacing two sets of limits for the migration of eight metals to three sets:
- Finger paints are separated from modeling clay and have their own set of limits
- ‘Textiles’ is included in the set of limits for ‘Coatings, writing materials, plastics, paper and paperboard’ (see Table 1)
- New requirements for phthalates in plastic, coating and rubber materials in two categories of toys:
- ≤ 0.1% for the sum of BBP, DBP and DEHP in toys
- ≤ 0.1% for the sum of BBP, DBP, DEHP, DIDP, DINP and DNOP in toys for children under three years of age which can be placed in the mouth
According to the WTO document, comments are accepted until January 13, 2020.
Highlights of the three sets of limits for eight metals are summarized in Table 1.
|WTO Document Number 19-7760, November 14, 2019
TIS 685 Part-25XX (20XX)): Toys: Safety Requirements: Part 1 – Requirements as a Mandatory Standard
|Soluble element||Coatings, writing materials, plastics, paper and paperboard, and textiles||Modelling clay||Finger paints|
|Antimony||≤ 60 mg/kg||≤ 60 mg/kg||≤ 10 mg/kg|
||≤ 25 mg/kg||≤ 25 mg/kg||≤ 10 mg/kg|
|Barium||≤ 1,000 mg/kg||≤ 250 mg/kg||≤ 350 mg/kg|
||≤ 75 mg/kg||≤ 50 mg/kg||≤ 15 mg/kg|
||≤ 60 mg/kg||≤ 25 mg/kg||≤ 25 mg/kg|
|Lead||≤ 90 mg/kg||≤ 90 mg/kg||≤ 25 mg/kg|
|Mercury||≤ 60 mg/kg||≤ 25 mg/kg||≤ 10 mg/kg|
|Selenium||≤ 500 mg/kg||≤ 500 mg/kg||≤ 50 mg/kg|
|1||BBP||Benzyl butyl phthalate|
SGS is committed to providing information about development in regulations for consumer products as complimentary services. Through a global network of laboratories, SGS provides a wide range of services including physical/mechanical testing, analytical testing and consultancy work for technical and non-technical parameters applicable to a comprehensive range of consumer products. Please do not hesitate to contact us for further information.
For enquiries, please contact:
Global Information and Innovation Manager
Tel:(+852) 2774 7420
Hardlines/Toys Laboratory Manager
t: +66 2 294 7485
© SGS Group Management SA - 2019 - All rights reserved - SGS is a registered trademark of SGS Group Management SA. This is a publication of SGS, except for 3rd parties’ contents submitted or licensed for use by SGS. SGS neither endorses nor disapproves said 3rd parties contents. This publication is intended to provide technical information and shall not be considered an exhaustive treatment of any subject treated. It is strictly educational and does not replace any legal requirements or applicable regulations. It is not intended to constitute consulting or professional advice. The information contained herein is provided “as is” and SGS does not warrant that it will be error-free or will meet any particular criteria of performance or quality. Do not quote or refer any information herein without SGS’s prior written consent.